View NESG3033M14_4147783.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NPN SILICON GERMANIUM RF TRANSISTOR
NESG3033M14
NPN SiGe RF TRANSISTOR FOR LOW NOISE, HIGH-GAIN AMPLIFICATION 4-PIN LEAD-LESS MINIMOLD (M14, 1208 PKG)
FEATURES
* The device is an ideal choice for low noise, high-gain amplification NF = 0.6 dB TYP. @ VCE = 2 V, IC = 6 mA, f = 2.0 GHz * Maximum stable power gain: MSG = 20.5 dB TYP. @ VCE = 2 V, IC = 15 mA, f = 2.0 GHz * SiGe HBT technology (UHS3) adopted: fmax = 110 GHz * This product is improvement of ESD of NESG3032M14. * 4-pin lead-less minimold (M14, 1208 PKG)
ORDERING INFORMATION
Part Number NESG3033M14 Order Number NESG3033M14-A Package 4-pin lead-less minimold (M14, 1208 PKG) NESG3033M14-T3 NESG3033M14-T3-A (Pb-Free) Quantity 50 pcs (Non reel) 10 kpcs/reel Supplying Form * 8 mm wide embossed taping * Pin 1 (Collector), Pin 4 (Emitter) face the perforation side of the tape
Remark To order evaluation samples, contact your nearby sales office. Unit sample quantity is 50 pcs.
ABSOLUTE MAXIMUM RATINGS (TA = +25C)
Parameter Collector to Base Voltage Collector to Emitter Voltage Base Current Collector Current Total Power Dissipation Junction Temperature Storage Temperature Symbol VCBO
Note 1
Ratings 5.0 4.3 12 35 150 150 -65 to +150
Unit V V mA mA mW C C
VCEO IB
Note 1
IC Ptot
Note 2
Tj Tstg
Notes 1. VCBO and IB are limited by the permissible current of the protection element. 2. Mounted on 1.08 cm2 x 1.0 mm (t) glass epoxy PWB
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
Document No. PU10640EJ01V0DS (1st edition) Date Published September 2006 NS CP(K)
2006
NESG3033M14
RECOMMENDED OPERATING RANGE (TA = +25C)
Parameter Input Power Base Feedback Resister Symbol Pin Rb MIN. - - TYP. - - MAX. 0 100 Unit dBm k
Remark When the voltage return bias circuit like the figure below is used, a current increase is seen because the ESD protection element is turned on when recommended range of motion in the above table is exceeded. However, there is no influence of reliability, including deterioration.
Rb
Bias Choke
2
Data Sheet PU10640EJ01V0DS
NESG3033M14
ELECTRICAL CHARACTERISTICS (TA = +25C)
Parameter DC Characteristics Collector Cut-off Current Emitter Cut-off Current DC Current Gain RF Characteristics Insertion Power Gain Noise Figure Associated Gain Reverse Transfer Capacitance Maximum Stable Power Gain S21e NF Ga Cre
Note 2 Note 2
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
ICBO IEBO hFE
Note 1
VCB = 5 V, IE = 0 mA VEB = 1 V, IC = 0 mA VCE = 2 V, IC = 6 mA
- - 220
- - 300
100 100 380
nA nA -
VCE = 2 V, IC = 15 mA, f = 2.0 GHz VCE = 2 V, IC = 6 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt VCE = 2 V, IC = 6 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt VCB = 2 V, IE = 0 mA, f = 1 MHz VCE = 2 V, IC = 15 mA, f = 2.0 GHz VCE = 3 V, IC (set) = 20 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt VCE = 3 V, IC (set) = 20 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt
15.0 - - - 17.5 - -
17.5 0.60 17.5 0.15 20.5
- 0.85 - 0.25 - - -
dB dB dB pF dB
MSG
3
Gain 1 dB Compression Output Power 3rd Order Intermodulation Distortion Output Intercept Point
PO (1 dB) OIP3
12.5 24.0
dBm dBm
Notes 1. Pulse measurement: PW 350 s, Duty Cycle 2% 2. Collector to base capacitance when the emitter grounded 3. MSG = S21 S12
hFE CLASSIFICATION
Rank Marking hFE Value FB zL 220 to 380
Data Sheet PU10640EJ01V0DS
3
NESG3033M14
PACKAGE DIMENSIONS 4-PIN LEAD-LESS MINIMOLD (M14, 1208 PKG) (UNIT: mm)
1.00.05 0.8+0.07 -0.05
3
2
4
zL
1
0.50.05
PIN CONNECTIONS
1. 2. 3. 4. Collector Emitter Base NC (Connected with Pin 2)
4
Data Sheet PU10640EJ01V0DS
0.11+0.1 -0.05
0.150.05
1.2+0.07 -0.05
0.8
NESG3033M14
* The information in this document is current as of September, 2006. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above).
M8E 02. 11-1
Data Sheet PU10640EJ01V0DS
5
NESG3033M14
For further information, please contact NEC Compound Semiconductor Devices Hong Kong Limited E-mail: contact@ncsd-hk.necel.com Hong Kong Head Office TEL: +852-3107-7303 FAX: +852-3107-7309 Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Korea Branch Office TEL: +82-2-558-2120 FAX: +82-2-558-5209 NEC Electronics (Europe) GmbH http://www.eu.necel.com/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 Compound Semiconductor Devices Division NEC Electronics Corporation URL: http://www.ncsd.necel.com/
0604
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of NESG3033M14

	To Download NESG3033M14 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .